D-Link DSN-2100-10 - xStack Storage Area Network Array Hard Drive Uživatelská příručka Strana 22
- Strana / 36
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
22 Chapter 3 Installing the DSN-2100 Storage System
3.6 Connecting the Power Cords
The DSN-2100 storage system has a two power receptacles. Both must be used to connect
the DSN-2100 to an AC outlet:
1. Plug the female end of the power cord into the 3-pronged power connectors on the back
of the DSN-2100 storage system. Plug the other end of the power cord into a working AC
outlet that is not controlled by a wall switch.
2. Repeat the previous step using the second power cable and power receptacle on the
DSN-2100 storage system. For best results, all both power receptacles should be on a
different circuit.
Although the DSN-2100 storage system can operate temporarily with only
two AC power connections, an audio alarm will sound until both power
receptacles are used.
3.7 Powering-on the DSN-2100 Storage System
To power-on the DSN-2100 storage system, press the power switch on the back panel. When
the DSN-2100 storage system powers-on, the following actions occur:
The DSN-2100 storage system Power LED turns green (see Figure 2-1).
The DSN-2100 storage system runs its power-on procedure (~4 minutes), then the
Ready/Fault LED turns green and drive LEDs may flash.
The completion of the power-on process can be verified as indicated in Table 3-2.
Table 3-2. Verifying Completion of the DSN-2100 Storage System Power-on Process
If the DSN-2100 Storage System… Verify the Power-on Process by…
Has no front panel Ready/Fault LED Wait five minutes after powering-on the DSN-2100 storage
system.
Has a front panel Ready/Fault LED. The LED turns green when the startup process completes. If
the LED turns red, reboot the DSN-2100 storage system. If the
problem persists, contact Technical Support.
Diagnostic port is connected to a PC via a diagnostic cable. The message RCP sequence complete appears on the PC
monitor. After verifying this message, disconnect the PC from
the diagnostic port.
After the DSN-2100 storage system powers-on for the first time, it automatically loads the
factory-default configuration settings. If necessary, you can use the xStack Storage
Management Center to change these settings to suit your requirements. For a description of
the array’s factory-default configuration settings and how to change them, refer to the
xStack Storage Management Center User's Guide.
- Managed SAN Solution 1
- DSN-2100 1
- Hardware Reference Guide 1
- Trademarks 2
- Safety Information 3
- Compliance Information 3
- Notice of Export Controls 3
- Document Revision Level 4
- Preface 5
- Contact Information 6
- Contents 7
- Chapter 1 Introduction 9
- 1.2 Benefits and Features 10
- 1.3 System Overview 10
- Chapter 2 DSN-2100 Layout 11
- 2.1 Front Panel Components 12
- 2.1.1 Front Vents 13
- 2.2 Rear Panel Components 14
- Switch Description 15
- 3.1 Site Considerations 18
- 3.1.3 Rack-mount Guidelines 19
- Battery Pack 23
- System and buffer memory 23
- SATA drives 23
- Fans 23
- Power supplies 23
- A.2 Installing Memory 26
- A.3.1 Drive and Tray Removal 28
- A.4 Replacing a Fan 33
Související produkty a manuály pro Interní pevné disky D-Link DSN-2100-10 - xStack Storage Area Network Array Hard Drive
(42 stránky)Alfa Romeo MITO manuály
Uživatelské manuály a uživatelské příručky pro Auta Alfa Romeo MITO.
Poskytujeme 1 manuály pdf Alfa Romeo MITO ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentáře k této Příručce